高层民用建筑电气防火设计

针对高层民用建筑电气防火设计问题，结合现行国家标准的规定进行了探讨，提出了消防电源及其配电、应急照明等设计原则。     

舰船主动力装置故障隔离与参数估计方法

针对舰船主动力装置结构复杂、故障种类多和系统不确定性等故障诊断问题，提出采用基于双因果键合图模型的定量故障隔离与参数估计方法。根据系统传感器配置方案，建立双因果键合图模型，通过因果路径分析，推导得到系统解析冗余关系，并获得故障特征矩阵。建立系统线性分式变换键合图模型，开展故障仿真，将其与双因果键合图模型耦合，在MATLAB/Simulink环境中进行仿真试验，实现了舰船主动力装置的故障隔离与参数估计。结果表明：对双因果键合图模型因果路径分析，可以避免手动推导系统解析冗余关系的繁杂过程；基于其部件构造方程的分析可以有效实现系统故障隔离与参数估计，实时跟踪和预测故障状态。     

开口电极在海水中的电场特性研究

利用稳恒电磁场理论,通过基本假设和单个电极电场计算公式的推导,计算了某一深度平面的电场值,绘制了平面分布图。接着利用相似理论进行了模型缩比实验,测量了二电极电场在某一平面上的分布值,绘制了平面分布图,进行了基本特性分析。该结果对进行船舶电场模拟和海缆断点探寻等工作,具有很好的参考价值。     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.     

Experimental investigation on dynamic response and damage models of circular RC columns subjected to underwater explosions

Reinforced concrete (RC) columns are widely used as supporting structures for high-piled wharfs. The study of damage model of a RC column due to underwater explosion is a critical issue to assess the wharf’s antiknock security. In this study, the dynamic response and damage model of circular RC columns subjected to underwater explosions were investigated by means of scaled-down experiment models. Experiments were carried out in a 10.0 m diameter tank with the water depth of 2.25 m, under different explosive quantities (0.025 kg–1.6 kg), stand-off distances (0.0 m–7.0 m), and detonation depths (0.25 m–2.0 m). The shock wave load and dynamic response of experiment models were measured by configuring sensors of pressure, acceleration, strain, and displacement. Then, the load distribution characteristics, time history of test data, and damage models related to present conditions were obtained and discussed. Three damage models, including bending failure, bending-shear failure and punching failure, were identified. In addition, the experience model of shock wave loads on the surface of a RC column was proposed for engineering application.     

基于正态分布曲线的分段式变步长LMS算法

针对传统最小均方误差(Least Mean Square, LMS)自适应滤波算法由于步长固定,在解决稳态误差与收敛性之间的关系时,始终处于矛盾状态的问题,在对传统的固定步长LMS自适应滤波算法分析的基础上,根据变步长LMS自适应滤波算法的步长调整原则,通过构造步长因子与误差信号的非线性函数,提出了一种基于正态分布曲线的分段式变步长LMS自适应滤波算法,并分析了参数取值对算法性能的影响。针对实际信号处理过程中参考信号难以选取的问题,提出了一种基于分裂阵的参考信号选取方法。理论和海试数据分析结果表明:该算法的收敛速度和稳态误差明显优于固定步长的LMS自适应滤波算法和基于Sigmoid函数的变步长LMS自适应滤波算法。     

舰船汽力装置变工况性能的图形化处理

应用现代计算机图形处理方法动态地描述舰用蒸汽动力装置及其设备的变工况性能数据，包括用图形交互的方式输入、显示和保存数据等关键内容．该方法已用于实际工程分析．     

钢弦测功仪的智能化改造研究与实现

将过去传统的钢弦式测功仪用计算机技术进行数据采集与处理 ,从而提高了其测量速度及测试精度 ,数据更为准确、稳定 ,可在 1台仪器上同时连续高速动态显示被测主轴的转速、功率、扭矩 ,并自动保存数据 .人机界面强 ,智能化程度高 ,具有很强的数据后处理及文件形成功能 .     

概率风险评估在核电站消防安全管理中的应用

介绍了概率风险评估与火灾概率风险评估的基本概念,详细论述了概率风险评估的主要内容及其在核电站火灾安全管理中的应用。     

Fragment spatial distribution of prismatic casing under internal explosive loading

Non-cylindrical casings filled with explosives have undergone rapid development in warhead design and explosion control. The fragment spatial distribution of prismatic casings is more complex than that of traditional cylindrical casings. In this study, numerical and experimental investigations into the fragment spatial distribution of a prismatic casing were conducted. A new numerical method, which adds the Lagrangian marker points to the Eulerian grid, was proposed to track the multi-material interfaces and material dynamic fractures. Physical quantity mappings between the Lagrangian marker points and Eulerian grid were achieved by their topological relationship. Thereafter, the fragment spatial distributions of the prismatic casing with different fragment sizes, fragment shapes, and casing geometries were obtained using the numerical method. Moreover, fragment spatial distribution experiments were conducted on the prismatic casing with different fragment sizes and shapes, and the experimental data were compared with the numerical results. The effects of the fragment and casing geometry on the fragment spatial distributions were determined by analyzing the numerical results and experimental data. Finally, a formula including the casing geometry parameters was fitted to predict the fragment spatial distribution of the prismatic casing under internal explosive loading.